US $550.0010 - 40,000 metric ton
US $350.0040,001 - 999,999 metric ton
Paramtents
Standard BS, GB, ASTM
Standard BS 1387, BS 1139, BS 4568, BS EN 39, GB/T 13793-1992, ASTM A106-2006, ASTM A53-2007
Grade 16Mn, A53-A369, Q195-Q345
Grade 16Mn, A53(A,B), A106(B,C), Q235, Q345, Q195, Q215
Thickness 0.45 - 8 inch
Section Shape Round
Outer Diameter 21.3 - 273.1 mm
Secondary Or Not Non-secondary
Application Structure Pipe
Technique ERW
Certification ISO9001-2000
Surface Treatment Galvanized
Special Pipe Thick Wall Pipe
GI YESTEEL
specification 1/2''-10''
Standard BS 1387, BS 4568, BS EN 39, GB/T 3091-200
Outer Diameter 21.3 - 273.1 mm
Surface Treatment GALVANIZED
Packging & Delivery
Min Order10 metric ton
Briefing
Detailed
Hot-dipped galvanized steel pipe
1).O.D.:1/2''-10''(21.3mm-273.3mm)
2).W.T.:0.75mm-8mm
5).Length:3m-10m
6)Zinc:40,50,60,80micron
Nominal size | Out diameter | Thickness |
inch | mm | mm |
1/2" | 21.3 | 1-2.8 |
3/4" | 26.9 | 1-2.8 |
1" | 33.7 | 1-3.2 |
11/4" | 42.4 | 1-3.5 |
11/2" | 48.3 | 1.5-3.5 |
2" | 60.3 | 1.5-3.5 |
21/2" | 76.1 | 1.5-3.75 |
3" | 88.9 | 4 |
4" | 114.3 | 4 |
5" | 139.7 | 4 |
6" | 168.3 | 4.5 |
8" | 219.1 | 4.0-6.0 |
1.TOLERANCE
a) On Specified OD + 0.5mm (Ovality 0.5mm)
:b) The Inside Diameter of ubes shall allow insertion of a guage of 37.7mm dia for a minimum length of 200mm.
:c) On Wall thickness -10%
:d) The mass deviation on a single tube shall not exceed -7.5% of the specified mass.
2. ENDS
: Cut cleanly and nominally square with the axis of the tube and free from excessive burrs.
3. PROPERTIES
:a) Chemical (Maximum) C - 0.20%, SI - 0.05%, MN - 1.40%, P - 0.04%, S - 0.045%, AL - Min. 0.02%.
:b) Mechanical = UTS - 340 to 520 N/mm2, YS - 235 N/mm2 (minimum) & %Elongation on 5.65 S0 - 24% (minimum).
4. FLATTENING TEST WELD AT 90 DEGREES (COLD)
a) For weld : Distance between the platens, measured under load is not greater than 75% of the OD of tube.
b) For Material :Distance Between the platens, measured under load is not greater than 60% of the OD of tube.
5. STRAIGHTNESS
: 1 in 500 (In 1 meter it should not exceed 3mm).
6. ZINC COATING
: Minimum local coating thickness on the outside surface 40 microns.
(GALVANIZING)
7. MARKING
: a) We can emboss mill sign "EN 39 UTP 3 or 4." online at every one meter interval over the length of pipe.
b) We can do online stencilling as per customer needs.
8. PACKING
: Hexagonal type.
9. MILL TEST CERTIFICATE
:We can issue a MTC, certifying that the tubes supplied comply with this Standard.
网络文化经营许可证:浙网文[2013]0268-027号|增值电信业务经营许可证:浙B2-20080224-1 2007-2024 Tradevv.com. All rights reserved.